fbpx
Bóka tíma

Cquartz SiC (Silica Carbide) Lakkvörn

To celebrate the end of the decade and ten years of Cquartz, we are proud to introduce the next evolution.  After intense research, development, and testing, CQuartz SiC is ready to continue where Tio2 left off!  As the name would suggest, this new formula also includes SiC (Silicon Carbide) for additional resistance against chemicals!  Not only that but CQuartz SiC greatly improves the ease of use, resistance to water (mineral) spots, and even amped up the gloss!  Finally, the slickness will leave you thrilled with the finished product!

Features:

  • Acid and alkyl chemical resistance from 2 ~ 13 pH.
  • Better water spots and minerals resistance.
  • Highly smooth feeling.
  • Deep gloss.
  • Very easy application in any temperature.

Tech specifications:

  • Sliding angle: 10 ̊.
  • Water contact angle: 110 ̊.
  • Heat tolerance: 392 ̊ F.
  • Application temp. range: 50 ̊F ~100 ̊ F.
  • Surface finish: High slickness.
  • Gloss: Mirror Shine.
  • Chemical resistance: 2 ~ 13 pH.
  • Mineral resistance: High (easy to remove).
  • Salt resistance: Medium.

Preparation:

  • If contamination exists, CarPro Iron X and clay your vehicle before polishing.

  • To gain the most from Cquartz your vehicle should have all surfaces 100% clean and paint polished to a high level.

  • Use CarPro Reflect to achieve an incredible high gloss finish in less time with no fillers. 

  • Use CarPro Eraser to remove any oils leftover after polishing – This is critical to ensure durability of CQuartz.

  • We recommend coating removal towels: CarPro 2face microfiber towel

Directions: Use only in good ambient lighting

  1. Wrap a 4″ microfiber suede around the grey side of applicator block.

  2. Shake CQuartz.

  3. Slowly open bottle and drag one line of product down the applicator. 

  4. Spread across paint in a criss cross pattern approximately 2 sq ft at a time depending on conditions.

  5. Buff off about 5 minutes later when you see a white haze begin to form. (3~15 minutes depends on conditions) – see additional tips below) using a CarPro No Lint Ultra Towel 16″ x 16″.  

  6. Be sure to remove all excess residue when wiping off.

  7. Switch out the 4″ Suedes every 2+/- panels.

  8. Additional coats may be applied with 45-60 minutes or wait until the following day if you are beyond 90 minutes.  CarPro recommends 2 coats. You may apply additional coats if you wish.

  9. We do NOT recommend adding Reload on top unless you wish to do so after it is fully cured or in future.  SiC is very slick on is own and in fact more slick then Reload.

After Tips:

  • Keep surface dry for at least 3 hours after application (For best results keep dry for 24 hours).
  • Gently wipe any water off the surface during the first 24 hours after application.
  • Avoid detergents and chemicals for 5 days after application.

Coating Maintenance:

  1. Wash with CarPro Reset regularly.
  2. Wash Mitt: 

Precautions:

  • Do not apply in direct sun or on hot surface.
  • Do not re-use 4″ suede applicators.
  • Do not re-use the towels you used to buff off with on paint.
  • Wear hand protection
  • Wear respiratory protection such as a painters mask.

8.900kr. – 12.490kr.

Vörur okkar eru til sölu hjá okkur í Dalshrauni 24.

Sambærilegar vörur

Related products

BónSvítan

Dalshraun 24
220 Hafnarfjörður

773 6653
bonsvitan@bonsvitan.is

© Bónsvítan ehf.
Kt: 420721-2770
VSK: 141818
Opnunartími
Virka daga: 08:00 – 17:00
Helgar: Lokað
Scroll to Top